Wheelset 28" Disc GRV | NONPLUS Components 6-hole hubs | ENVE Gravel Carbon Rims
intended use : Gravel GRV
This light yet stable wheel set is the first choice for dedicated gravel or cross bikers. The noble selection of components guarantees you high reliability and a long service life.
hubs
Three decades of experience in the development and production of hubs leave their mark, albeit "very light".
Over the years, the head of development at NONPLUS COMPONENTS, Christian Jenny, has been able to accumulate immense specialist and practical knowledge, which in 2016, after finding an investor, led to the production of the first prototypes.
In order to be able to guarantee the precise production of the hubs, the company Frank Präzisionsteile GmbH from Murr in Baden-Württemberg, which is also the investor, took over the production. A little later, in 2018, NON+ was registered as a trademark. Since then, the wheels have not stood still at one of the most innovative think tanks for bike components in Germany. New concepts are constantly being developed and patents registered in order to be able to set new standards in the future.
The NONPLUS rear wheel hub is a masterpiece of technology and unique due to its weight in connection with approval for almost every application in cycling. The black anodized oversized hub body forms the heart of the hub, around which everything revolves. Two bearings, dimensioned according to the load, support the hub body on a 17 mm axle , two further bearings carry the freewheel and the microgap end caps keep dirt and water away from the inside of the hub. A brake disc mount, which extends directly to the spoke flange, ensures optimal transmission of the braking forces. The patented freewheel mechanism is hidden on the opposite side. The unique conical gearing has a contact surface that is approx. 400% larger than conventional spur gearing and thus enables maximum power transmission with minimal wear. The special, very elaborately manufactured tooth back, together with the hard anodized surface, ensures low abrasion and thus also increases the service life. The 45-fold toothing results in a maximum idle travel of 8°. This gives you direct propulsion, for example in difficult passages, when you need it and you don't lose any valuable time when sprinting to the finish line.
rims
ENVE carbon rims are developed by ENVE in the USA and manufactured to the highest quality standards at the headquarters in Utah. The ENVE engineers have years of experience with the use of carbon in the field of cycling and know what requirements a top product like these carbon rims must meet. At ENVE, everything is done to use the advantages of carbon and eliminate its disadvantages. Stiff and extremely light rims were developed in which all fibers can run without interruption, which corresponds to the best possible utilization of the material strengths. This principle was perfected in the spoke holes, in which continuous fiber strands form the mount for the spoke nipples. Aluminum inserts, which are common with other carbon rims, can therefore be dispensed with during production. This reduces the weight and at the same time allows significantly higher spoke tensions, which in turn allow the construction of stiffer wheels.
Impeller construction at R2-Bike
Our wheels are assembled entirely by hand by our wheel builders. During the entire construction, it is important that not only the concentricity is right, but also that the spoke tension is as even as possible. The special care allows us to give a lifetime guarantee against broken spokes, as long as this is not caused by violence!
You will also receive the following services with our wheels:
A universal impeller bag for all common sizes.
A spare spoke + nipple in all required spoke lengths to be able to repair the impeller at short notice even after an accident.
A free initial check of the impeller, where the resulting work is completely free! Only shipping costs are charged.
A crash replacement promise. If your wheel is damaged due to force majeure, we will rebuild your wheel once. We grant a 100% discount on all labor costs and only charge for the material!
Technical specifications:
intended use : Gravel GRV
Wheel size: 28" (ETRTO: 622 x 23)
Rim Type: Clincher (clincher and folding)
Brake type: disc brake
Brake disc mount: 6-hole
weights:
1163g (lightest variant: 12x100 mm + 12x142 mm, Sapim CX-Ray)
1235g (heaviest variant: 12x100 mm + 12x142 mm, Sapim Race)
Notice:
Due to manufacturing variations in all components, deviations in weight are possible. The information is usually determined without rim tape, valves and decals/rim stickers.
The specified delivery time refers to the usual time it takes to assemble the wheelset and does not reflect the availability of the individual parts.
Scope of delivery:
1x complete wheelset, fully assembled (hubs, rims, spokes and nipples)
2x ENVE Tubeless Kit (already mounted on request)
1x wheel bag
4x spare spokes including nipples
1x assembly certificate
2x hologram stickers