SHIMANO SLX complete Group M7000 1x11
SHIMANO SLX Upgrade Kit M7000 1x11
With the SLX components you get top switching performance at an unbeatable low price.
The SLX M7000 1-speed crankset was created for drivers who count for low weight and high load capacity in the uncompromising MTB use. From Cross Country to All Mountain, she masters every challenge. With a universal Q-factor of 175 mm, a stable and drive-resistant 24 mm steel shaft and a torsion-resistant, weight-saving Hollowtech II crank arm construction.
The Shimano SM-CR70 chainrings are made of a 3D composite composite of fiberglass reinforced plastic and stainless steel teeth. This material mix gives the chainrings a very high rigidity and low weight. The special retention technology keeps the chain securely in place even without a chain guide.
The bearing is done Shimano typical high-quality, sealed deep groove ball bearings.
The Shimano SLX shifters trigger with their precise mechanics fast gear changes. The years of experience on the part of Shimano brings a well-balanced balance of low operating forces and at the same time pronounced feedback from the levers - interconnection is hardly possible.
The levers offer 11-speed step grading and are compatible only with 11-speed Dyna-Sys11 rear derailleurs. The SL-M7000 I-Spec II shift lever is attached to the handlebar via the brake lever clamp. With the help of the I-Spec II bracket, the cockpit of the wheel is not only visually pimped, another advantage is the lower total weight (shift lever / brake lever) compared to the variant with clamp.
The 11-speed SLX rear derailleur is in terms of function and switching performance of the XT rear derailleur in nothing, only the slightly higher weight could be considered a minus point. Like the big brother of Shimano's top series, it delivers fast and smooth shifts. With the revised Shadow + technology, the bias of the chain can be adjusted in two stages via a small lever on the rear derailleur. So you can decide whether the chain should run quietly with less chain tension, or taut for rough lenght must be tightened. Shadow construction reduces the lateral projection of the rear derailleur and thus reduces the risk of hanging with the rear derailleur on sticks and stones. The used scraper rolls with sealed bearings, run very clean and offer a long life!
The SLX 11-speed cassette offers excellent switching performance, acceptable weight and high wear resistance. With a fine gradation optimized for 1x11 drives, the gear changes succeed extremely precisely and with short switching pauses. An intelligent material mix of aluminum and steel increases the life, but at the same time reduces the weight of the cassette. For example, the main body (spider), the lock ring and the largest sprocket are made of aluminum to save weight. The remaining sprockets, however, are made of steel, which not only reduces the wear, but also generates more rigidity so as to be able to convert the entire force into propulsion.
The directional Shimano 105 | SLX chain for 11-speed drives offers with its adapted geometry of the chain links excellent switching performance in every situation. Even mud and dirt, the sophisticated design offers little attack surface. In combination with SIL-TEC, Shimano's new surface coating, ultra-low friction is generated. Compared to simple coatings, SIL-TEC is a very special coating process. Thanks to the use of embedded fluorine particles, system performance is improved. The coating also reduces wear, driving noise and sliding friction, is dirt-repellent and abrasion-resistant, which significantly increases the durability of the components treated with SIL-Tec.
Thanks to Servo Wave technology, the brake shines with fast response and a very well adjustable pressure point. The bleeding is very easy by means of one-way bleeding, but is usually only necessary when shortening the brake line.
The ergonomically shaped levers can be optimally operated with one or two fingers and adjusted within reach without tools. Shimano shifters can be attached to the brake levers with I-Spec II bracket to save the extra lever clamp.
For increased stability Ice-Tech sintered metal coverings with cooling fins are installed. In addition, we recommend using the optional Ice-Tech brake discs.
Lightweight brake discs made of stainless steel with dirt-repellent design. The perfectly tuned friction ring ensures optimum braking performance in dry and wet conditions. The disc is compatible with both organic and sintered metal brake pads. Reliable and easy installation thanks to screws and locking plate.
Weight: from 1988g (without brakes and without bottom bracket)
Note: Weights may vary depending on the selected configuration.
Any needed tools and mounting accessories can be found in our shop.
Other customers have also bought the following items