label
Easy contact

Service & Support
+49 351 811 975 90


E-Mail Support Mail support
support@r2-bike.com


Follow us

Follow us on FacebookFollow us on Facebook
Follow us on youTube


Join Newsletter Newsletter
... join & enjoy

header image

NOTUBES Tubelesskit Race | Starter Kit

NOTUBES Tubelesskit Race | Starter Kit NOTUBES Tubelesskit Race | Starter Kit
  • Availability: available from stock
  • Item no.: 21399
  • Category:
  • from : 57,50 €
  • including 19% VAT., Plus Shipping
  • List Price: 70,88 €
  • You save 19%, that is 13,38 €
Loading ...

  • Yellow Tape

Description

Notubes Tubelesskit Race | starter Kit

Optimized starter set in the world of tubeless cycling.
The new Race formula contains nearly twice as many standard sealing crystals, plus the new, special XL crystals. It is now possible that, up to 8mm large hole immediately and permanently sealed.
The kit is suitable for use with NoTubes ZTR rims (such as Olympic, podium, Alpine, Crest, 355, Arch, Race, Flow)


Technical specifications:

Sealing: by the Race formula is sealed an up to 8 mm hole immediately and permanently
Duration: 2-6 months (depending on intended use)
Quantity: sufficient for about 16 fillings tires (a 59 ml, for tires with 1.0-2.4 inch width)
Effective range: -30 ° C
Environment: completely made from natural ingredients and therefore very environmentally friendly


Delivery:

- 1 x yellow tape roll (enough for about 5 wheels)
- 2 x Notubes ZTR valves
- 1 x 946 ml NoTubes Race sealing milk

NoTubes Yellow tape with either 21 or 25 mm width
- 21 mm: Crest, Olympic, Alpine, 355, Race, Podium, Arch, Arch EX
- 25 mm: Arch EX, Arch, Flow, Flow EX



The Assembly:

1. Rim degrease eg with brake disk cleaner (these you'll find under the heading Cleaning and accessories in our shop)

2. Make a 20 cm strip of the tape under train, sticking bubbles through the valve hole.
IMPORTANT: strips carefully rub hard with no bubbles!

3. A ply Rim Tape Lay / under train (voltage) stick.
IMPORTANT: The two ends must overlap at the valve hole, there to have the tape in two layers to secure the valve pin. The entire tape must be firmly rubbed blisters.

4. preparting Small hole for the valve. Then push through the valve and secure with Rädelmutter.

5. raise tire completely and inflate with compressed air. The tire jumps audibly from about 2.2 bar in the correct position on the rim flange. If you worked clean, keep the air even without sealing milk for about 10 minutes.

6. deflate again. Tire between rim and carcass rub Spüli liquor. This guarantees the best fit and takes the transition additionally surface tension of the latex milk, so that these better distributed in the pores. Unscrew the valve core from the valve.
Caution: It does not bend valve bolt.
Then fill at least 60 ml of milk sealing by taking down of the tire at a position in the tire. Valve core screw again and inflate again with compressed air.
IMPORTANT: Due to the enormous and rapid sealing force, it is necessary the NoTubes Race sealing milk to fill directly into the tire, as it would otherwise clog injectors, valves or smaller bottles filled immediately!

7. impeller now pivot and fluff up several minutes to allow liquid spreads. The optimum distribution is carried out at the wheel is spinning. If at one point even air out the affected area turn down and shake vigorously again.

For normal standard rims as Mavic, Sun etc. please use depending rim width and size the standard kit, Freeride Kit, Downhill Kit or cyclocross kit, which you can also buy in our shop!

Other customers have also bought the following items