DT SWISS Rear Wheel 27,5" | 650B HX 1501 Spline One Boost Hybrid | E-Bike

DT SWISS rear wheel 27,5 "| 650B HX 1501 Spline One Boost Hybrid | E-Bike

With the hybrid wheel sets, DT-Swiss is launching the first series of impellers, which have been specifically optimized for use on eMTBs. Not only the system weight at eMTBs is higher and leads to higher loads for the wheels, also many trails and rough passages can be driven at significantly higher speeds. In addition to this, the drive system generates higher driving torques which are required to be placed on the ground and require stiffer wheels. The engineers at DT-Swiss have taken this requirement into account and optimized all components of their proven Spline wheel sets for use on MTBs.

The HX 1501 Spline One wheels are the lightest wheels with an aluminum rim under the DT SwissHybrid wheels. In terms of durability and stiffness, however, no compromises were made. The low weight was achieved by the use of high-quality Alumium alloys. With a 30- or 35-millimeter gap, the rim plus tires give up to 3.5 inches, even at low air pressures, a good support. With a clearance of up to 150 kilos of system weight (driver, clothing, bike), the HX 1501 bikes offer enough reserves for heavy riders on rough trails.


Hybrid rear wheel hub

The hybrid hub has an oversized housing, a heavy duty axle and extra reinforced spoke mountings. Over-dimensioned bearings and a free-floating steel body ensure high robustness and durability. The tried and tested DT-Swiss toothed disc freewheel is also made from hardened steel at the hybrid hub and has been extended to 24 teeth for a more direct response. These adjustments allow the larger torques of e-bike drives to be absorbed by the hub. The hybrid hub has a very low weight compared to a standard MTB hub. The spline hub flanges for Straigthpull spokes also make the hub optically an eyecatcher.


Hybrid spokes

In order to transfer the higher drive forces to the rims, DT-Swiss developed special oversized hybrid spokes. They consist of the same high-performance steel alloy as all the tried and tested DT Swiss spokes. However, the Straightpull hybrid spokes are equipped with reinforced and oversized fuel heads, which together with the DT Pro Lock Squorx nipples ensure that every watt on the rim arrives.


Hybrid wheels

Due to the system's increased overall weight, the rims of e-bikes must be able to push away more than on conventional MTBs. At first glance, the hybrid rims differ from the standard DT Swiss enduro rims. So they have the same Tubelessready rim profile with load-optimized cross-sections. However, in the case of the hybrid rims, material strength and strength were increased at the critical points in order to maintain the higher loads permanently.


Technical specifications:

intended use : E-Bike, Tour, All Mountain, Trail
Wheel size: 27.5 "(ETRTO: 584 x 30 | 35 mm)
Type of rim: clincher (wire and folding)
Brake type: only for disc brake
Brake disc mount: 6-hole (IS2000)
Material: aluminum, steel
Internal width: 30 or 35 mm
External width: 35 or 40 mm
Wheel height: 21 mm
Number of holes: 28 holes
axle type : 12x148 mm Plug-in axle (BOOST / Outboard)
bearing : 4x oversized industrial storage
Seal: labyrinth rubber seals
Freilauf Compatibility: 9-, 10-, 11-speed Shimano or SRAM XD (conversion kit included)
Freewheel type: toothed disc freewheel, 24 detent points per wheel revolution
Spokes: 28x DT Swiss hybrid spokes, straightpull
Tubeless capable: yes
Recommended tire width: 1.85 "-3.5" (47-89 mm)
Maximum driver weight: 150 Kg (driver, bike, clothing and possibly luggage)
Color: black, gray-blue logos

Weights (manufacturer's data):

1076g (30mm rim)
1131g (35mm rim)


Scope of delivery: Rear wheel, Tubeless Tape, Tubeless valve, Freewheel for SRAM XD